Skip to content
Free shipping on eligible items at $75+Tire, wheel & large-item exclusions apply

Wiseco Pistons and Top End Kits

RideWell is an authorized Wiseco dealer. Every piston, ring set and top end kit on this page is genuine Wiseco product, brand new, sourced through Wiseco's own distribution network and covered by the full manufacturer warranty. No grey market, no old stock bought off a closing shop.

Wiseco has been forging pistons in Mentor, Ohio since 1941, and they are the default choice when a stock cast piston is not going to survive what you have planned. Every Wiseco piston is forged rather than cast, which means a denser, stronger grain structure and far more tolerance for heat, detonation and sustained high rpm.

We stock Wiseco for ATVs, UTVs and side-by-sides, dirt bikes, motorcycles, snowmobiles and personal watercraft.

Browse Wiseco parts

Wiseco products

1,213 products

Find parts for your vehicle

Select year, make and model. No account needed.

Loading vehicle options…

Vehicle results use listed supplier applications. Apparel, tools and items without a listed application can be browsed separately; check size and specifications.

What we carry

Piston kits
A forged piston with matched rings, wrist pin and circlips, sized to your engine's bore. The standard replacement when you are refreshing a tired top end or going back to spec after a failure.
Top end kits
Everything in a piston kit plus the gaskets and seals you need to actually close the engine back up: base gasket, head gasket, valve seals where applicable. Ordering the kit is almost always cheaper than assembling the same parts individually, and it means you are not stopping halfway through a rebuild because one gasket did not arrive.
Piston rings
Replacement ring sets for Wiseco pistons, sold separately when the piston is still in spec but the rings are worn.
Clutch baskets and drivetrain
Forged billet clutch baskets and related components for applications where the stock part is a known weak point.
Garage Buddy complete engine rebuild kits
Wiseco's all-in-one kits, covering the bottom end as well as the top: crankshaft, bearings, seals and gaskets alongside the piston.

Why forged, and when it matters

Cast pistons are fine in a stock engine ridden at stock power. Forged pistons are made by pressing a heated aluminum billet into shape under enormous pressure, which aligns the grain and eliminates the porosity a casting leaves behind. The practical result is a piston that survives detonation and heat that would crack a cast one.

You want forged if you are running higher compression, a big bore, aggressive porting, race fuel, a turbo or nitrous, extended full-throttle riding such as dunes or long trail days, or if you have already lost one piston and want to know why it will not happen again.

If your machine is stock and stays stock, a Wiseco piston is still an upgrade in durability. It is just not a requirement.

Getting the right part

Wiseco parts are sized precisely, and the difference between a 95mm and a 95.5mm piston is the difference between a rebuild and a very expensive mistake. Two things decide fitment:

1. Your machine's year, make and model. Manufacturers change bore sizes and pin dimensions mid generation more often than you would expect.

2. Your current bore size. If the cylinder has been bored before, you need an oversize piston to match, not a standard one. Measure, or have your machine shop measure, before ordering.

Not sure? Email us the year, make, model and your measured bore, and we will confirm the exact part number before you buy. That costs nothing and is a lot cheaper than a restocking fee.

Get help choosing your Wiseco part

Frequently asked

Read our piston ring gap guide

What ring gap should I run?

Wiseco supplies a recommended gap with every ring set, and it varies by bore size and application. As a rule, forced induction and nitrous applications need a wider gap than naturally aspirated ones. Always gap to the instruction sheet in your kit rather than a generic figure, and always check the gap in the actual cylinder the ring will run in.

Which way do the rings face?

Ring orientation matters. Most Wiseco ring sets are marked, and the mark faces up toward the piston crown. The instruction sheet in your kit is definitive; installing a ring upside down will cause it to seat badly and burn oil.

How do I break in a new piston?

Follow Wiseco's break-in instructions for your specific kit. Broadly: get the engine to operating temperature without loading it, then run varied throttle with no sustained high rpm and no lugging for the first few heat cycles. Change the oil early. The rings seat in the first hour of running, and how you spend that hour determines how well the engine seals for the rest of its life.

Do I need a top end kit or just a piston?

If you are opening the engine, you need the gaskets, and a top end kit is normally cheaper than the same parts bought separately. Buy the piston alone only if you already have the gaskets in hand.

Is it covered by warranty?

Yes. We are an authorized Wiseco dealer, so every part we sell carries the full manufacturer's warranty and we handle claims for you. Note that manufacturer warranties generally exclude competition and racing use, commercial use, and damage caused by improper installation or tuning. Full detail is on our shipping and returns page.

Are these genuine Wiseco parts?

Every part on this page is genuine Wiseco, brand new and in the manufacturer's packaging. RideWell is an authorized Wiseco dealer, which is what makes the manufacturer warranty valid on anything you buy here. Counterfeit and grey market pistons are a real problem in this category, and the warranty is the thing you lose first when you buy outside the authorized network.

Ordering from us

RideWell is an authorized Wiseco dealer. See our shipping and returns policies for current charges, dispatch times, return eligibility and manufacturer warranty terms.

Shipping and warranty policyReturns policy